[. . . ] Hardware Specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. PRODUCT SOFTWARE SPECIFICATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. 1. General Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4. 2. Configuration Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5. [. . . ] Memory
SDRAM Flash 8 MBytes 1 MBytes
3. 2. 2 Power Adapter
Power Voltage DC 5 Volt + 5%, AC Adapter AC 100V-240V
4. General Function
a) Standard : IEEE 802. 11b/IEEE 802. 3 b) RTS/CTS Handshake c) Duplicate detection and recovery d) Wired Equivalent Privacy Algorithm (WEP) 64/128/256 Bits e) Distributed Coordination Function: CSMA/CA, Back of Procedure, ACK Procedure, Retransmission of unacknowledged frames f) Authentication Algorithm
4
g) Fragment / De-fragment h) Preamble Long / Short i) Roaming Function j) Power Saving Management k) Beacon Generation l) Access Control m) HTTPD/DHCP Client n) Filtering function o) Bridge Mode for Building to Building Transmission p) AP Client Mode q) DHCP Server (Option) r) DHCP Client s) Finger print security feature (Option)
4. 2. Interface
a) Web Configuration b) Windows Configuration Utility
5. 15. 247 and 15. 109 ETS 300 328, ETS 300 826, EN60950 and CE-Mark Telec (Japan), VCCI (Option) WiFi Compliant
6. Anti-Static Voltage
Static voltage tests by 4kV in body should not cause system fail.
6. 1. 2. Vibration Test
The vibration test is under the Frequency and amplitude 10~25 1mm in vertical and horizontal direction by 30 minutes that should not cause any damage on product.
6. 1. 3. Package Drop Test
Dropping the package from the height of 50cm for each of the six(6) faces onto the hard-wood floor will not cause any product damage.
5
6. 2. Temperature Range Operating: Storage: -0 - +55 (Except RF output power and sensitivity) -20 - +70
6. 2. 2. Temperature Shock
The one cycle of reliability test is keeping -30 for 2 hours, switching temperature up to +60 within one hour, and testing at +60 by 2 hours, and switching temperature to -30 within one hour. INSTALLATION AND CONFIGURATION
7. 1 Access Point Utility Installation and Configuration
7. 1. 1 Utility Installation 1. Windows will automatically start Installshield Wizard or run "E:\22M. exe" then following screen will appear.
6
4. 7. 1. 2 Utility Configuration Please Click following icon in the screen.
Caution: If you select one or more Access points, then click Apply in following screens. Type in "admin" as the user name and "admin" as the password. Then, click AP settings.
AP Settings
The AP setting screen will now appear. Enter a unique name access point for the Access Point and your wireless network's SSID, select the channel at which the network broadband its wireless signal. Then, click Advanced Settings.
8
Advanced Setup
On this page, you can set the AP mode plus following settings:
Beacon Interval By default, it is set to 100mps. If you encounter any date flow, only minor modifications are recommended. The value indicates how much of the network resources devoted to recovering packet errors. If you have decreased this value and experience high packet error rates, you can increase it again, but will likely decrease overall network performance. DTIM Interval shows the client how often the beacon contains a delivery traffic indication message. [. . . ] Then, click the Advanced Setting.
13
Advanced Setup
On this page, you can set the AP mode plus following settings:
Beacon Interval By default, it is set to 100mps. If you encounter any date flow, only minor modifications are recommended. The value indicates how much of the network resources devoted to recovering packet errors. If you have decreased this value and experience high packet error rates, you can increase it again, but will likely decrease overall network performance. [. . . ]